Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
We've stumbled upon this post on Installing A Bathtub listed below on the internet and accepted it made sense to discuss it with you on this page.
Installing a bathtub isn't exactly rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Changing an old tub with a brand-new one is also a reasonably hard task. If the old bathtub is conveniently available, the task can move speedily; if you need to open up a wall to eliminate the old bathtub as well as place the brand-new tub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will need a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the job and are comfortable trying it. Rather than hiring a professional to take over a halfway-completed task, it is much better to consider utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This write-up will help you set up a brand-new bathtub in your shower room if you have actually currently acquired a new tub as well as do not require to alter the arrangement of your previous supply of water pipes.
Your tools as well as material list must make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be rather bothersome due to the restricted gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in area between the tap and the sink. Secure the faucet in position with the manufacturer provided backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the tub until the spirit level reads level.
To set up faucets, fit the bottom of the furthest adaptable faucet adapter to the proper supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally examine the overflow electrical outlet as well as the normal outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has been made use of at the very least when as this will resolve it right into its final setting.
Getting ready for the Installment
To start with, the supporting structure provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last position.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split a rigid seal, causing the water to permeate the wall surface between the bathroom and the tiling, resulting in issues with moisture and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and installations. They are offered in tubes as well as cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can crack relatively very early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the market. It is a good idea to fit the floor tiles utilizing waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our section about How to Install a Bathtub. Thanks a lot for taking a few minutes to read our piece of content. Don't hesitate to take the opportunity to share this blog entry if you enjoyed reading it. Thank you for taking the time to read it.
Need fast action? Dial. Report this page